Microwave-accelerated Claisen rearrangements of allyl tetronates and tetramates

[3,3]-Sigmatropic rearrangements of allyl tetronates and allyl tetramates to give 3-allyltetronic or -tetramic acids, respectively, proceed within 20-60 min under microwave irradiation (300 W, 130-190 °C). Consecutive (homo)sigmatropic [1,5] H-shifts such as oxa-ene reactions are promoted less effectively, which allows the isolation of Claisen intermediates of sigmatropic domino sequences, in contrast to conventional heating.     

The glow curve structure for the LiF:Mg,Cu,Na,Si TL detector with dopants concentrations and sintering temperatures

The glow curve structures for LiF:Mg,Cu,Na,Si TL detectors with various dopant concentrations and sintering temperatures were investigated for the improvement of the glow curve structure and sensitivity of the TL detector. The dopant concentrations were varied over the following ranges: Mg (0–0.25 mol%), Cu (0–0.07 mol%), Na and Si (0–1.5 mol%). With increasing Cu concentration, the intensity of the main peak was intensified and reached a maximum at a concentration of 0.05 mol%. The high-temperature peak was reduced. The dependency of the main peak intensity on the Mg concentration exhibits a sharp maximum at 0.2 mol%. The intensity of the high-temperature peak tends to rise slightly with increasing Mg concentration. It was found that the optimum concentrations of the dopants in the LiF:Mg,Cu,Na,Si TL material are Mg: 0.2 mol%, Cu: 0.05 mol%, Na and Si: 0.9 mol%. The dependency of the main peak intensity on sintering temperature exhibits a very sharp maximum at 830°C. The high-temperature peak was rapidly reduced after 825°C.     

Synthesis and association of poly(N,N‐dimethylacrylamide) copolymers with perfluorocarbon pendent groups connected through polyethylene‐glycol tethers

The synthesis is reported of copolymers of N,N‐dimethylacrylamide (DMA) and methacrylates containing 2,2′‐dihydroperfluorodecanoyl (RF) groups separated from the methacrylate by long polyethylene glycol (PEG) tether groups (between 1000 and 14,000 Da). At concentrations of between 1 and 8 wt % the copolymers with macromonomer contents of 1 mol % or less give gels in organic solvents such as dioxane, THF, or methanol, as well as in water. Given the low molecular weights, this indicates very efficient association of very low numbers of RF groups. Association and gel formation is enormously enhanced in the presence of longer PEG tethers. This is consistent with smaller poly(N,N,‐dimethylacrylamide) (PDMA) intermolecular excluded volume effects that are mediated by the longer PEG tethers and possibly by the incompatibility of PEG and PDMA that may lead to the formation of PEG microdomains. This increases the local concentrations of the RF groups in the PEO domains that are not diluted by the PDMA chains, as would be the case in the absence of PEG tethers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 360–373, 2004     

Dependence of the kinetics of the anionic polymerization of methyl methacrylate on the concentration in active centers

Studies on the anionic polymerization of methyl methacrylate in tetrahydrofuran and in the presence of sparteine have revealed a beneficial effect due to this additive, resulting in a decrease in the extent of termination. Better control of the definition of the polymers formed can thus be achieved in the presence of this additive. On the other hand, macromolecular engineering requires a range of active species concentrations lower than 10^?3 mol L^?1 and particularly the synthesis of polymers of high molar masses. For a better understanding of the mechanism of chain growth under such concentration conditions, the kinetics of polymerization have been investigated with a technique based on adiabatic calorimetry. Sparteine has been found to lack sufficient cation‐binding power to prevent the propagating enolate ion pairs from aggregating. The rate constant of propagation of nonaggregated species has been estimated, as well as the aggregation constant of equilibrium. For very low initiator concentrations, termination reactions have been shown to profoundly alter the control of the polymerization and to prevent a quantitative monomer conversion. Theoretical maximal conversions have been calculated from kinetic data and compare well with the experimental values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4964–4975, 2004     

Polymerization of 1,3‐dienes with functional groups. III. Free‐radical polymerization of N,N‐diethyl‐2‐methylene‐3‐butenamide

Free‐radical homo‐ and copolymerization behavior of N,N‐diethyl‐2‐methylene‐3‐butenamide (DEA) was investigated. When the monomer was heated in bulk at 60 °C for 25 h without initiator, rubbery, solid gel was formed by the thermal polymerization. No such reaction was observed when the polymerization was carried out in 2 mol/L of benzene solution with with 1 mol % of azobisisobutyronitrile (AIBN) as an initiator. The polymerization rate (R_p) equation was R_p ∝ [DEA]^1.1[AIBN]^0.51, and the overall activation energy of polymerization was calculated 84.1 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure where both 1,4‐E and 1,4‐Z structures were included. From the product analysis of the telomerization with tert‐butylmercaptan as a telogen, the modes of monomer addition were estimated to be both 1,4‐ and 4,1‐addition. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were also carried out in benzene solution at 60 °C. In the copolymerization with styrene, the monomer reactivity ratios obtained were r₁ = 5.83 and r₂ = 0.05, and the Q and e values were Q = 8.4 and e = 0.33, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 999–1007, 2004     

Stereological simulations of asymmetric polymerization in channels of bile acid inclusion compounds: A detailed analysis of the monomer arrangements in the channels

We studied simulations by computer graphics to estimate the steric mechanism of the asymmetric polymerization of prochiral diene monomers in channels of inclusion compounds of steroidal bile acids, such as deoxycholic acid (DCA) and cholic acid. We applied a hierarchization method to interpret the crystal structures of bile acids, clarifying that the chiral host molecules associated to form characteristic 2₁-helical assemblies with uneven surfaces. A detailed analysis of the uneven channels in a close-packing state indicated that there were many possible arrangements of the monomers in the channels. The plausible arrangements in the channel could explain a previous study, which showed that the polymerization in the DCA channel yielded chiral polymers with a predominant configuration from prochiral diene monomers, such as 2-methyl-trans-1,3-pentadiene. On the basis of such simulation studies of the arrangements of guest monomers in the channel, we examined a plausible steric mechanism for asymmetric inclusion polymerization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4648–4655, 2004     

Comparative behavior of polybutadiene and polynorbornene‐based latices prepared by dispersion ring‐opening metathesis polymerization with a poly(ethylene oxide) macromonomer

This study critically examines the similarities and differences between poly(ethylene oxide) (PEO) stabilized latices of polynorbornene and polybutadiene. Features such as the kinetics of copolymerization of norbornene and cyclooctadiene with a macromonomer of PEO, the particles' size and morphology, the type of copolymer formed, and the stability of these latices were investigated and the results obtained are considered. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2705–2716, 2004     

Metallo‐supramolecular block copolymer micelles: Improved preparation and characterization

Micelles prepared from amphiphilic block copolymers in which a poly(styrene) segment is connected to a poly(ethylene oxide) block via a bis‐(2,2′:6′,2″‐terpyridine‐ruthenium) complex have been intensely studied. In most cases, the micelle populations were found to be strongly heterogeneous in size because of massive micelle/micelle aggregation. In the study reported in this article we tried to improve the homogeneity of the micelle population. The variant preparation procedure developed, which is described here, was used to prepare two “protomer”‐type micelles: PS₂₀‐[Ru]‐PEO₇₀ and PS₂₀‐[Ru]‐PEO₃₇₅. The dropwise addition of water to a solution of the compounds in dimethylformamide was replaced by the controlled addition of water by a syringe pump. The resulting micelles were characterized by sedimentation velocity and sedimentation equilibrium analyses in an analytical ultracentrifuge and by transmission electron microscopy of negatively stained samples. Sedimentation analysis showed virtually unimodal size distributions, in contrast to the findings on micelles prepared previously. PS₂₀‐[Ru]‐PEO₇₀ micelles were found to have an average molar mass of 318,000 g/mol (corresponding to 53 protomers per micelle, which is distinctly less than after micelle preparation by the standard method) and an average hydrodynamic diameter (d_h) of 18 nm. For PS₂₀‐[Ru]‐PEO₃₇₅ micelles, the corresponding values were M = 603,000 g/mol (31 protomers per micelle) and d_h = 34 nm. The latter particles were found to be identical to the “equilibrium” micelles prepared in pure water. Both micelle types had a very narrow molar mass distribution but a much broader distribution of s values and thus of hydrodynamic diameters. This indicates a conformational heterogeneity that is stable on the time scale of sedimentation velocity analysis. The findings from electron microscopy were in disagreement with those from the sedimentation analysis both in average micelle diameter and in the width of the distributions, apparently because of imperfections in the staining procedure. The preparation procedure described also may be useful in micelle formation from other types of protomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4458–4465, 2004     

A nucleophilic substitution reaction in microemulsions based on either an alcohol ethoxylate or a sugar surfactant

A nucleophilic substitution reaction between 4-tert-butylbenzyl bromide and a series of iodide salts has been performed in oil-in-water microemulsions based on either a fatty alcohol ethoxylate or a sugar surfactant. The reaction kinetics was compared with the kinetics of the same reaction performed in a microhomogeneous reaction medium, d-MeOH. Previous results showing a particularly high reactivity in the microemulsion based on the fatty alcohol ethoxylate was confirmed. It was shown that in both microemulsions the reaction rate was almost independent of the choice of counterion to iodide. This indicates that complexation of the cation with the surfactant headgroup, which, in particular, could have taken place with surfactants containing oligooxyethylene chains (a “crown ether effect”), seems not to be of importance.

¹²⁷I NMR studies, as well as quadrupole splitting experiments performed by ²H NMR, indicate that there is a certain accumulation of iodide at the oil–water interface of the microemulsions. It is difficult to draw any quantitative conclusions in this respect, however.

The results obtained in this study, combined with results from previous investigations of the same reaction, indicate that the unexpectedly high reactivity obtained in the microemulsion based on a surfactant containing an oligooxyethylene headgroup is most probably due to the nucleophile being poorly solvated when present in the headgroup layer of such a microemulsion. Poorly solvated anions are known to be highly reactive nucleophiles.